Daktronics KE-1010-7.6-RG Bedienungsanleitung

DakTicker® KE-1010 Series Display Manual ED-11634 Rev 8 15 February 2005 331 32nd Ave PO Box 51

Introduction 1-41.4 Definitions Cabinet: The cabinet refers to the metal frame of the display (back, bottom, top), and may be expanded to include the

1.5 Daktronics Nomenclature To fully understand some Daktronics drawings, such as schematics, it is necessary to know how various components are labe

Most circuit boards and components within this display carry a label that lists the part number of the unit. If a circuit board or assembly is not li

Section 2: Mechanical Installation Note: Daktronics engineering staff must approve any changes made to the displays. If any modifications are made,

2.2 Display Mounting Reference Drawings: Shop Drawings...Refer to Appendix A It is the custom

Mechanical Installation 2-31. Before attempting to connect the sections, check their alignment in relation to each other. If the alignment is off,

Mechanical Installation 2-41. If it has not already been done, unpack the display and check for any damage that may have occurred during shipping. 2

Section 3: Electrical Installation 3.1 Signal Cables The conductor connector used in the network is an industry standard, 6-pin RJ-11 or an 8-pin

The crimping tool is then used to crimp the RJ connector onto the cable. The RJ connector is locked into a special socket in the tool. The stripped wi

Electrical Installation 3-33.2 Power Reference Drawings: Shop Drawings ... Refer to Appendix

ED-11634 Product 1182 Rev 8 – 15 February 2005 Copyright © 2003-2005 All rights reserved. While every

Note: Displays must be earth grounded according to national and local electrical codes. Power Connection – Power Cord Connected Displays The DAKTicker

Ethernet Connection For those tickers that use an Ethernet system for communications, a network connection will be made from the network hub or switc

Figure 13: Shift Board 3.5 Master to Master Connections Most displays systems will consist of a master display or a master and one or

Electrical Installation 3-73.6 First Time Turn On After all connections are made, it is time to turn on the display for the first time. 1. Plug t

Section 4: Maintenance & Troubleshooting IMPORTANT NOTES: 1. Disconnect power before any repair or maintenance work is done on the display! 2.

4.2 Display Interior LED Module Replacement Reference Drawings: Schematics ...Refer to App

Replacing a Power Supply Reference Drawings: Component Layout Drawings ... Refer to Appendix A Schematics...

Figure 18: Shift Board 5. The card is attached to the inside of the display with four #6-32 hex-head screws. Remove the attaching screws and careful

To replace a controller: 1. Disconnect the 120 VAC power to the master section. 2. Remove the face panel per Section 4.1. 3. Remove the two LED m

Table of Contents iTable of Contents Section 1: Introduction...1-1 1.1 S

Maintenance & Troubleshooting 4-64.4 Sign Maintenance Visual Structural Inspection Visual inspection should be done annually to check paint and f

Maintenance & Troubleshooting 4-7Display is garbled or sequence is shifted. • Check the settings on the data feed PC. • Check signal connec

Maintenance & Troubleshooting 4-8Wall Mounting Bracket; 30° Tilt 0A-1182-0018 DataStreamer Manual ED-13649 4.7 Daktronics Exchange/Repair &

Maintenance & Troubleshooting 4-9Packaging for Return: Package and pad the item well so that it will not be damaged in shipment. Electronic c

Appendix A: Reference Drawings A-1Appendix A: Reference Drawings Refer to Section 1 for information on how to read the drawing number and interpret

Table of Contents ii Ticker Controller Functionality LED Indicators ...4-6 4.5 Troubleshooting...

List of Figures iiiList of Figures Figure 1: Drawing Label...

Section 1: Introduction This manual explains the installation and maintenance of the Daktronics DAKTicker™ series KE-1010 displays. For questions re

All references to drawing numbers, appendices, figures or other manuals are presented in bold typeface, as shown below. “Refer to Drawing B-206146 in

Daktronics KE-1010 displays are all aluminum construction and may consist of separate sections. Tickers are available in tri-color (red, green and am