Daktronics DF-12xx Bedienungsanleitung

DataMaster™ Outdoor LED Gasoline Price Displays DF-1024/DF-1026 Series DF-1200 Series Insta

Gasoline Price D-1 Quick Start Reference Appendix D: DataMaster Gasoline Price Quick Start Reference DataTime Gasoline Price Displays Quick Sta

Introduction 1-1 Section 1: Introduction This manual explains the installation, maintenance and troubleshooting of the Daktronics DataMaster™ DF-

1-2 Introduction Figure 1, below, illustrates the Daktronics drawing label. The drawing number is located in the lower-right corner of each drawing

Introduction 1-3 1.1 Safety Precautions Important Safeguards: 1. Read and understand these instructions before installing your display. 2. Do no

1-4 Introduction Modem The modem is a standard communication interface that utilizes standard phone transmission lines. The phone company assigns e

Introduction 1-5 The DataMaster model numbers are described as follows: DF-102X-HH-C 1.4 Component Identification The following list inclu

1-6 Introduction Mirror/slave: receives power and a digit harness from the master but does not have a driver. Power Supply: Converts AC line volt

Electrical Installation 2-1 Section 2: Mechanical Installation Note: Daktronics does not guarantee the warranty in situations where the display

2-2 Electrical Installation Full Cabinet Models with backlit product ID panels left of digits Dimensions and Weight

Electrical Installation 2-3 2.2 Lifting the Display Model DF- displays are shipped equipped with 3/8" eyebolts that are used for lifting

Electrical Installation 3-1 Section 3: Electrical Installation Daktronics outdoor displays are UL listed and tested to CSA standards for outdo

3-2 Electrical Installation WARNING: It is critical that the display circuit be fused at 15 A, and that all conductors used must be designed to pass

Electrical Installation 3-3 Grounding Reference Drawings: Enclosed Driver, 4 Column Reference ...Drawing A-184918 Disp

3-4 Electrical Installation 3.3 Lightning Protection The use of a disconnect near the display to completely cut all current-carrying lines signific

Electrical Installation 3-5 To gain access to the driver enclosure, open the access door and remove the cover from the enclosure. Refer to the E

3-6 Electrical Installation Note: The cable from the j-box to the display needs to be routed through conduit or the display pole to protect it from

Electrical Installation 3-7 If using the DataMaster handheld controller at an indoor location, only the two, 22 AWG, signal wires (white and gr

3-8 Electrical Installation Connection from J-box to Server Radio Enclosure J-Box TB2 on Server Pin# FunctionCable Color Pin# Function Pin 1

Electrical Installation 3-9 Notes: 1. The cable from the client radio to the display can to be routed through conduit or the display pole t

ED-15177 Product 1319 Rev 2 – 27 April 2005 DAKTRONICS, INC. Copyright © 2004-2005 All rights reserved. While ev

3-10 Electrical Installation 1. Using the DB9M to DB9F serial cable, connect from the DataMaster controller to the modem/j-box, at the “DB9 Male, D

Electrical Installation 3-11 Host/Client Definitions One driver at each sign installation is designated as the “host driver.” This driver rece

3-12 Electrical Installation Binary Address Settings Address 1 2 3 4 5 6 7 8 1 ON OFF OFF OFF OFF OFF OFF OFF 2 O

Maintenance and 4-1 Troubleshooting Section 4: Maintenance and Troubleshooting IMPORTANT NOTES: 1. Disconnect power before doing any repair o

4-2 Maintenance and Troubleshooting For the front-access modules in this series, all internal electronic components and digits can be reached by open

Maintenance and 4-3 Troubleshooting 3. The digits are secured to the inside of the panel with fixed machine screws, spacers, and push nuts. Remo

4-4 Maintenance and Troubleshooting 5. Reconnect the power/signal connector. Note: This is a keyed connector it will attach in one way only. Do not

Maintenance and 4-5 Troubleshooting To replace the driver in the display enclosure: 1. Open the digit panel or display face panel as describe

4-6 Maintenance and Troubleshooting The following table lists the functions of the various jacks, including those that are not used in this applicati

Maintenance and 4-7 Troubleshooting In the display, the signal surge suppression board is an inline device used to filter the current loop data

4-8 Maintenance and Troubleshooting 1. The power LED (DS1) should remain lit while power is applied to the modem. 2. The modem RX (DS3) and TX (DS

Maintenance and 4-9 Troubleshooting 4.5 Troubleshooting This section lists potential problems with the display, indicates possible causes, and su

4-10 Maintenance and Troubleshooting Some DataMaster displays have their own built-in troubleshooting mechanism. Failures that may occur in the displ

Maintenance and 4-11 Troubleshooting Power On Self-Test: A useful troubleshooting tool is the power on self-test the host driver performs every t

4-12 Maintenance and Troubleshooting J-box, signal converter, radio 0A-1279-0161 RJ11 to RJ45, M-M,

Maintenance and 4-13 Troubleshooting Digit, 18" 7-segment, red, w/ faceplate 0A-1192-2227 Digit, 18" 7-segment, amber, w/ faceplate

4-14 Maintenance and Troubleshooting 4.7 Daktronics Exchange and Repair and Return Programs To serve customers' repair and maintena

Maintenance and 4-15 Troubleshooting working days from the invoice date, you will be credited for the amount on the second invoice, minus a resto

Gas Price 5-1 Display Operation Section 5: Gas Price Display Operation These sections describe the DataMaster 100 controller, and how it is use

Reproduction Reference ED-15177 – P1319 DataMaster Gasoline Price Displays 1. This page is for reproduction reference only and will not be includ

5-2 Gas Price Display Operation Figure 24 illustrates the DM-100 insert used to control the displays. For more details on the insert, refer to the Da

Gas Price 5-3 Display Operation The controller will then list the “Current Function,” if it is Gas Price you can continue, otherwise at the next

5-4 Gas Price Display Operation Menu Items Pressing the <MENU> key accesses the following settings: 1. Price Line 1 2. Price Line 2 3. Pric

Gas Price 5-5 Display Operation Modifying Price Line Settings The gas price can be modified either by pressing the <EDIT> key during opera

5-6 Gas Price Display Operation LED Test Select menu item 6, LED Test, to test the LED digits on the display. LCD Screen Action LED TEST ENTER

Gas Price 5-7 Display Operation The modem will automatically disconnect from the display after a period of inactivity that is set by the Discon

5-8 Gas Price Display Operation Dimming The dimming level of the Gas Price display can be adjusted in two ways. A light sensor, mounted in the displa

Gas Price 5-9 Display Operation The following LCD prompt is shown for either Manual or Automatic dimming selections: LCD Screen Action INTE

5-10 Gas Price Display Operation 5.4 POS Installation and Interface Reference Drawings: System Riser Diagram; Point of Sale Configuration ... Drawi

Gas Price 5-11 Display Operation 7. Plug the transformer (T-1118) into an outlet, and connect the output to the power jack on the J-box. 8. En

5-12 Gas Price Display Operation Changing Prices: Each display line for which a price category is configured will automatically update when the price

Reference Drawings A-1 Appendix A: Reference Drawings Drawings in this manual are referenced by their last set of digits and the letter precedin

DATE:REV BY:1 06JUN02 JJSADDED LED LABELSADDED NEW NOTESDATE:REV BY:2 16 MAY 03 CJBUPDATE DRIVER FOR LATEST REVISIONOF MASC DRIVER.DATE:REV BY:3 27 NO

Table of Contents i Table of Contents Section 1: Introduction...

ii Table of Contents Section 5: Gas Price Display Operation...5-1 5.1 DataMaster 100 Overvi

List of Figures i List of Figures Figure 1: Daktronics Drawing Label ...

DataMaster FAQ B-1 Appendix B: DataMaster Frequently Asked Questions (FAQ) DataMaster FAQ...

Gasoline Price C-1 Quick Installation Reference Appendix C: DataMaster Gasoline Price Quick Installation Reference Gasoline Price Displays Direct