Daktronics BA-515 Bedienungsanleitung

Single-Section Outdoor Incandescent Scoreboards Installation, Maintenance, and Specifications Manual ED11974 All Sport® is a regi

Section 3: Specifications The following tables include all of the mechanical specifications, circuit specifications, and maximum power requirements f

3.1 Single-Section Scoreboards Note 1: Signal wires must be a minimum of 22- gauge with shield. Daktronics recommends using W-1234. Note 2: 120/240

Wattage Model Dimensions (Height, Width, Depth) Weight Uncrated (Crated) Digit Size and Matrix Lamp Maximum Power (See Note 2) Amps per Line (Sing

Wattage Model Dimensions (Height, Width, Depth) Weight Uncrated (Crated) Digit Size and Matrix Lamp Maximum Power (See Note 2) Amps per Line (Singl

Appendix B: Eyebolts Eyebolts...

ED7244 Copyright 1996-2001 Rev. 4 – 14 March 2001 Daktronics, Inc. Eyebolts Almost every display that leaves Daktronics is equipped with eyebolts f

Copyright 1996-2001 ED-7244 Daktronics, Inc. Rev. 4 – 14 March 2001 A B C D E No. Min. Proof Load (lbs.) Min. Break Load (lbs.) Stocked Min. Ef

Wattage Model Dimensions (Height, Width, Depth) Weight Uncrated (Crated) Digit Size and Matrix Lamp Maximum Power (See Note 2) Amps per Line (Sing

Wattage Power Model Dimensions (Height, Width, Depth) Weight Uncrated (Crated) Digit Size and Matrix Lamp Maximum (See Note 2) Amps per Line (Si

3.2 230 Volt Single-Section Scoreboards Note 1: Signal wires must be a minimum of 22-gauge with shield. Daktronics recommends using W-1234. Watta

Component Locations 4-1Section 4: Component Locations Use the following drawings to determine the location of scoreboard components. The drawi

Schematics 5-1Section 5: Schematics Use the following table to determine the schematic for your scoreboard model. The drawings are listed below i

Mechanical Installation 6-1Section 6: Mechanical Installation Mechanical installation consists of installing concrete footings and steel beams,

The columns and footings and all connection details must be designed and certified by a professional engineer licensed to practice in the state in whi

Mechanical Installation 6-3would be serious damage to the scoreboard. If you must use this method, ensure a minimum angle between the chain and s

to the Installation Specifications drawing for your model to determine the center-to-center distance of the poles. Review the illustrations of the mo

Mechanical Installation 6-56.4 Ad Panel Mounting Reference Drawings: Ad Panel Mounting...

Electrical Installation Section 7: Electrical Installation Reference Drawings: Components 8/16 Pos Power and Signal Entrance ...

Table of Contents Section 1: Introduction...1-1 1.1 H

Power Installation There are two basic considerations for power installation: installation with ground and neutral conductors provided, and installa

Electrical Installation 7-3The scoreboard must be connected to earth ground. Proper grounding is necessary for reliable equipment operation. It al

Section 8: Digit Maintenance and Troubleshooting IMPORTANT NOTES: Digit Maintenance 8-1 1. Disconnect power before doing any repair or maintenance

8.2 Lamp Replacement Reference Drawing: Digit Service... Dr

8.4 Fuses Reference Drawings: Layout, 16 Column Driver III ...Drawing A-123940 Layo

8.7 Lightning Protection The Transient Voltage Surge Suppresser (TVSS), located in the load center, reduces the brief surge induced into the power li

Description Location Daktronics Part No. 24" 4x7 shade screen 24" 4x7 digits 0S-1064-0002 15" 4x7 shade screen 15" 4x7 digit

Section 9: Team Name Message Centers Maintenance and Troubleshooting IMPORTANT NOTES: 1. Turn power off before doing any repair or maintenance w

Section 9: Team Name Message Centers Maintenance and Troubleshooting ...9-1 9.1 TNMC Schematics...

9.2 Service Procedures Reference Drawings: Lens Removal, Front Access. ... Drawing A-

Replacing a Lampbank When lampbanks are reattached to the lens assemblies, be certain the lamp sockets are seated tightly against the reflectors. Al

Individual Lamp Replacement Grasp the tab on the top center of the lens with the lamp-extracting tool (refer to Drawing A-99898). Pull the tab out

3. When finished, the stripping should be flush at the bottom. If the weather stripping is not tight or buckles anywhere on the lens assembly, it wil

Once the filters have been replaced, turn power back on. Make sure that the fans are turning properly. K Note: Turn the power OFF after checking the

As noted previously, 1,500 hours is equivalent to 83 days if the display is operated for 18 hours a day and the power to the display is turned off whe

9.11 Structural Inspection Perform a visual inspection annually. Check the paint and look for possible corrosion, especially at footings, structural

Symptom/Condition Possible Cause/Remedy Entire module does not work.  Check signal connection (ribbon cable)  Check power connections  Check tran

Part Description Daktronics Part No. Rear access module remover tool 0M-95441  0.032 feeler gauge, weatherstripping 0M-69133 Transformer, 120 V

Scoreboard Options 10-1 Section 10: Scoreboard Options The following options are available for Daktronics outdoor scoreboards to make the display

Section 1: Introduction 1.1 How To Use This Manual This manual explains the installation of Daktronics Single-Section, Outdoor Incandescent Scorebo

10-2 Scoreboard Options 10.2 Trumpet Horn Reference Drawings: Horn Installation ...

Scoreboard Options 10-3 4. Attach the horn enclosure to the inside of the scoreboard over the 5/32" holes using #10 tapping screws. 5. Atta

Appendix A: Reference Drawings A Drawings Digit Service...

Component Locations, CT-2001 ... Drawing A-126429 Component Locations, CT-2002 ...

1.3 Manual Overview This manual is divided into the following sections: Section 1: Contains an overview of the manual and explains the Daktronics d

If the defective equipment is not shipped to Daktronics within 30 working days from the invoice date, it is assumed you are purchasing the replacement

Section 2: Model Identification Use the following drawings to determine your scoreboard model number. The drawings, located in the Appendix, are inse